Auto Programmer
Total 41 Product(s)
We are professional auto programmer factory and supplier in China.We can produce auto programmer
according to your requirements.More types of auto programmer wanted,please contact us right now!
View:
MOTOROLA MC68HC705B16/32, MC68HC705X16/32, MC68HC05B6/8/16/32, MC68HC05X16/32 SMART EEPROM Programming Tool
Motorola MC68HC(7)11 EEPROM programming tool,ETL MOTO HC711,ETL HC68 In circuit / on board EEPROM programming. Communication with PC via a serial port CONFIG Register Programming Pin tester in both operation modes
Motorola MC68HC908AZ60, MC68HC05H12 Programmer Flash/EEPROM programmer with security passed On board EEPROM/FLASH programming. Communication with PC via a LPT port. High - Speed EEPROM/FLASH programming 64QFP ,100QFP and 52PLCC programming adapters
Motorola MC68HC912/MC68HC9S12 Flash/EEPROM programmer with security passed In circuit / on board EEPROM/FLASH programming. Communication with PC via a serial port High - Speed Programming 80QFP, 112QFP and 144QFP programming adapters
UPA Prog FULL With Adapters is a full featured low cost universal programmer for Odometer Correction series microcontrollers. The Programmer works on USB port. It will Program, Read and Verify Code Data, Write Lock Bits, Erase and Blank Check. All fuse and lock bits are programmable.
The XPROG-m programmer is designed to replace the earlier version of XPROG programmer.XPROG-m programmer is fully upward-compatible hardware with XPROG programmer and have many additional features.The XPROG-m supports in-circuit or on-board programming of Motrola 68HC05 , 68HC08, 68HC11, 68HC(S)12 , HC912, Launch X431 Diagun.
The TMS370 is for TI TMS Microcontroller development, car radios and car dashboards programming.
Support EEPROM programming of TMS374 MCU .Support immo function of DAEWOO,FIAT,KIA,PEUGEOT,RENAULT,etc
COM connector and support USB connector as well, Mileage correction reset your the mileage by directly input the data; Works on CPUs use NEC board, support userself upgration.
Easy to use Windows 98/2000/XP software: Read, Program, Erase Incremental Registers\EEPROM Erase time 5-10 minutes Supported both clock rates 4.0 and 8.0 MHz IC's. On-board EEPROM programming
List of supported vehicles: E38 E39 E46 E46 BOSCH E83 E65
M35080V6 Programmer, M35080V6 ERASER,ETL M35080V6 ERASER/Programmer Easy to use Windows 98/2000/XP software
supported more than 30,000 devices 1.extremely fast programming, one of the fastest programmers in this category. Programs 16-Mbit Flash memory less than 18 seconds 2.48-pins powerful pindrivers, no adapter required for any DIL devices 3.connector for in-circuit programming (ISP)
50825 supported devices by 2.64 version of SW (5. Nov. 2009) very fast programming, one of the fastest programmers in this category. Programs 64-Mbit NOR Flash memory less than 46 seconds and 1Gbit NAND Flash less than 120 sec.
STMicroelectronics ST62*: ST6240, ST6245, ST6249 NSC CR16*: CR16HCS5(9), CR16MCS5(9), CR16MES5(9), CR16MFS5(9), CR16MCT5/9, CR16HCT5/9 Motorola HC05*: MC68HC05B6, MC68HC05B8, MC68HC05B16, MC68HC705B16
Supported Devices STMicroelectronics ST62*: ST6240, ST6245, ST6249 NSC CR16*: CR16HCS5(9), CR16MCS5(9), CR16MES5(9), CR16MFS5(9), CR16MCT5/9, CR16HCT5/9 Motorola HC05*: MC68HC05B6, MC68HC05B8, MC68HC05B16, MC68HC705B16, MC68HC05B32, MC68HC05E6, MC68HC705E6, MC68HC05H12, MC68HC05L28, MC68HC05P3, MC68HC705P3*,MC68HC05X16, MC68HC05X32
CE and FCC approved. Programs high-density Flash memory devices at near theoretical minimum programming times (Program+verify INTEL28F320W18, 32Mb less than 13.5s ) Standard 48 pin universal pin-drivers come with universal package adapters to support all type of devices in same package with a single adapter.
XPROG,XPROG m v5.0 full authorization.All function work well. We can offer authorizations below and 13 pcs adapter.
This Tool is a frequency sweeper with 5V square wave output (Duty cycle 50%, effective frequency range from over 10kHz (max 50kHz) to 50Hz) .This tool can be also considered as a MCU version of the software TMS-374 Decoder ECU. The only difference between the two tools is that the MCU version works without a PC.
SH 705X programmer include all function for reading renesas RENESAS mcu ,like 64F7055 64F7058 64F7059.those mcu often use in HONDA .MAZDA,NISSAN and a lot of car.